防火卷簾門，是消防維保的朋友們經常需要測試的設備之一，遇到各種各樣的故障是很正常的。下面根據我十多年的經驗，給大家做以下內容的總結。

　　Fireproof rolling shutter doors are one of the equipment that fire maintenance friends often need to test, and it is normal to encounter various malfunctions. Based on my over ten years of experience, I would like to summarize the following content for everyone.

　　一、卷簾門常遇到哪些故障

　　1、 What are the common faults encountered by rolling shutter doors

　　卷簾門控制器故障指示燈亮

　　The fault indicator light of the rolling shutter door controller is on

　　卷簾門的故障指示燈亮起，是控制主板檢測到了非正常的情況。現在的主板功能都在不斷完善。遇到這種情況，可以分析以下幾種情況：

　　The malfunction indicator light of the rolling shutter door is on, indicating that the control motherboard has detected an abnormal situation. Nowadays, the functions of motherboards are constantly improving. In this situation, the following situations can be analyzed:

　　a：卷簾門主電源故障，比如說，缺相／錯相／欠壓／過壓，可以使用萬用表測量一下電源信號即可；

　　a: The main power supply of the rolling shutter door is faulty, such as phase loss/wrong phase/undervoltage/overvoltage. You can use a multimeter to measure the power signal;

　　b：備用電池故障，常見的就是電池無法充電導致欠壓。

　　b: Backup battery failure is commonly caused by undervoltage due to the inability to charge the battery.

　　c：主板供電電源故障，這種情況是因為控制箱內的變壓器損壞，無法提供正常的電源信號（通常電壓在15V左右，因主板不同，有所差異）。

　　c: The power supply failure of the motherboard is due to the damage of the transformer inside the control box, which cannot provide normal power signals (usually the voltage is around 15V, which varies depending on the motherboard brand).

　　d：卷簾門檢測不到限位信號。在主板上會有2個LED燈，顯示卷簾門處于上限或是下限。

　　d: The rolling shutter door cannot detect the limit signal. There will be 2 LED lights on the motherboard, indicating whether the rolling shutter door is at the upper or lower limit.

　　遇到故障指示燈亮起，大家可以參考上面的幾種情況逐一排查即可。

　　When the fault indicator light comes on, you can refer to the above situations to troubleshoot one by one.

　　2、卷簾門遠程控制按鈕無法提升卷簾（只能下降）

　　2. The remote control button of the rolling shutter door cannot lift the rolling shutter (it can only be lowered)

　　這種情況，通常是因為沒有主電源引起的，而且卷簾下降速度會很快（憑自重降落）。備用電池的作用就是在沒有主電源的情況下，接收到遠程控制盒的信號（任意按鈕都可以），打開電磁抱閘（就像汽車的手剎），卷簾在自身重力下下降。

　　This situation is usually caused by the lack of a main power source, and the rolling shutter descends quickly (by its own weight). The function of the backup battery is to receive a signal from the remote control box (any button can be pressed) in the absence of a main power source, open the electromagnetic brake (like a car handbrake), and the roller blind will descend under its own gravity.

　　3、遠程控制按鈕無法操作卷簾（注意不同于上個問題）

　　3. The remote control button cannot operate the roller blind (note different from the previous issue)

　　這種情況，可能的原因是按鈕損壞或是卷簾檢測不到正確的限位開關。可以通過主板上限位指示燈來判斷一下。

　　The possible reason for this situation is that the button is damaged or the roller blind cannot detect the correct limit switch. You can judge it by the upper limit indicator light on the motherboard.

　　大家也可以關注我的《消防工作筆記》，更詳細的了解這方面內容。

　　You can also follow my 'Fire Work Notes' to learn more about this aspect in detail.

　　二、維保人員更換卷簾門控制主板／控制器，需要怎么操作。

　　2、 How do maintenance personnel replace the control board/controller of the rolling shutter door.

　　有兩方面內容是需要注意的，一是遠程控制按鈕是否匹配，二是電機的安裝方向設置（左安裝還是右安裝）。

　　There are two aspects to pay attention to, one is whether the remote control button matches, and the other is the installation direction setting of the motor (left or right installation).

　　更換步驟如下：

　　The replacement steps are as follows:

　　1、將卷簾門下降半米左右（可以使用溫控釋放裝置，或者拉鏈來使卷簾下降）。

　　1. Lower the roller shutter door by about half a meter (you can use a temperature controlled release device or a zipper to lower the roller shutter).

　　2、更換完成主板，送電，打開控制器，點動卷簾下降的按鈕，觀察卷簾運行方向。若卷簾下降，則說明電機安裝方向設置正確，反之，則調整主板的撥碼開關。（選擇左安裝或是右安裝）

　　2. Replace the motherboard, power on, turn on the controller, press the button to lower the roller shutter, and observe the direction of the roller shutter operation. If the roller blind descends, it indicates that the motor installation direction is set correctly. Otherwise, adjust the dip switch on the motherboard. (Choose left or right installation)

　　3、根據主板的調試說明，設置卷簾是一步降落或是二步降落（有些卷簾不需要進行此操作）。

　　3. According to the debugging instructions of the motherboard, setting the roller shutter is either a one-step descent or a two-step descent (some roller shutters do not require this operation).

　　4、遠程控制按鈕的更換。卷簾的遠程控制按鈕，目前有兩種：多線形式和模擬量形式。多線形式，很好理解，就是線多，每個按鈕都對應一根線（有公共線）。模擬量形式，通常是3根線。注意，這兩種按鈕是不可以替換，必須與主板對應。

　　4. Replacement of remote control buttons. There are currently two types of remote control buttons for roller blinds: multi line form and analog form. Multi line form, easy to understand, means there are multiple lines, and each button corresponds to a line (with a common line). Analog form, usually consisting of 3 wires. Note that these two buttons cannot be replaced and must correspond to the motherboard.

　　本文由 濟南卷簾門  友情奉獻.更多有關的知識請點擊   http://m.santoncc.cn  真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors. For more related knowledge, please click http://m.santoncc.cn Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned