其實，卷簾門是現代建筑中不可缺少的防火設施，除此之外，大家還對其了解多少？知道該門的安裝步驟有哪些嗎？下面，跟隨濟南卷簾門廠家一起了解一下吧，希望能幫到大家。

In fact, rolling shutter doors are indispensable fire prevention facilities in modern buildings. In addition, how much do you know about them? Do you know the installation steps of the door? Now, let's follow the Jinan roller shutter door manufacturer to learn about it. I hope it can help you.

1、圖紙線

1. Drawing line

先測量室內空間和防火門安裝的尺寸。根據卷簾門中的卷軸數據，設計中間高度，在立柱或墻壁上，確定活動支撐板的中間位置，并釋放膨脹螺栓的中間十字線。卷簾門安裝的穩定性，數據測量須準確。

First measure the dimensions of indoor space and fire door installation. According to the reel data in the roller shutter door, design the middle height, determine the middle position of the movable support plate on the column or wall, and release the middle cross line of the expansion bolt. The installation stability of roller shutter door shall be measured accurately.

2、找到孔

2. Find the hole

當主支撐板的中間作為參考時，使用水平塑料管找到相應的動態支撐板和膨脹螺栓孔的中間，并仔細檢查它們形成的交叉線。

When the middle of the main support plate is used as a reference, use a horizontal plastic pipe to find the middle of the corresponding dynamic support plate and expansion bolt hole, and carefully check the cross line formed by them.

3、沖孔

3. Punching

（1）確定卷簾門具體位置后，使用沖擊鉆鉆出膨脹孔。請參考鉆孔所需的尺寸和位置。不要犯錯誤或不符合標準，收集的數據應準確。

(1) After determining the specific position of the roller shutter door, use the impact drill to drill the expansion hole. Please refer to the dimensions and locations required for drilling. Do not make mistakes or fail to meet standards, and the data collected should be accurate.

（2）注意鉆頭垂直于圓筒表面并形成90度的直角。如果各個螺孔碰到鋼筋，鉆頭可能無法進入，您可以參考實際情況并適當移動位置，但不能影響整體的堅固性和安裝效果。

(2) Note that the drill bit is perpendicular to the cylinder surface and forms a 90 degree right angle. If each screw hole touches the reinforcement, the drill may not be able to enter. You can refer to the actual situation and move the position appropriately, but the overall firmness and installation effect cannot be affected.

4、直支撐板

4. Straight support plate

（1）卷簾門安裝的時候如果有原支撐板，請將其安裝在主支撐板的前面。應預先連接驅動器支架，將其焊接在支撐板上，確保焊接牢固，然后用螺母固定。

(1) If there is an original support plate when installing the roller shutter door, please install it in front of the main support plate. The drive bracket shall be pre connected, welded on the support plate to ensure that the welding is firm, and then fixed with nuts.

您可以使用平墊圈來佩戴它。穿過支撐板的膨脹螺栓被擰緊，并且支撐板表面垂直于卷軸。

You can use flat washers to wear it. The expansion bolt passing through the support plate is tightened, and the surface of the support plate is perpendicular to the reel.

（2）按照上述方法安裝動力支撐板，但在擰緊螺栓之前，檢查水平管和動力支撐板的中間高度，是否與主動支撐板一致，水平應為控制在孔的高度300以內，請務必查看。如果沒有及時調整，請再次修理并避免返工。

(2) Install the power support plate according to the above method, but before tightening the bolts, check whether the middle height of the horizontal pipe and the power support plate is consistent with the active support plate. The level should be controlled within 300 of the hole height. Be sure to check. If it is not adjusted in time, please repair it again and avoid rework.

（3）對于輔助支撐或肋部分，一些支撐板由膨脹螺栓固定，但它們不夠穩定，可以通過補充支撐或加強肋使其更加固定。

(3) For the auxiliary support or rib part, some support plates are fixed by expansion bolts, but they are not stable enough. They can be more fixed by adding support or reinforcing ribs.

5、防火卷軸

5. Fireproof reel

(1)在卷簾門安裝卷軸之前，將掛板朝向該方向，將其安裝到卷軸上，然后將4-6塊窗簾連接到掛板上，并將其與卷軸上的線捆綁。

(1) Before installing the roller on the roller shutter door, first place the hanging plate in this direction, install it on the roller, then connect 4-6 curtains to the hanging plate, and bind them with the wires on the roller.

(2)吊裝卷軸固定抬起卷軸時，將軸承和座椅的光軸插入卷軸的端孔。對齊位置后，擰緊軸承固定螺栓。固定提升卷軸時，務必注意。設置專人指揮，梯子，腳手架，手帶等，并提前檢查，以盡量減少事故的發生。

(2) When lifting the reel, first insert the optical shaft of the bearing and seat into the end hole of the reel. After alignment, tighten the bearing retaining bolts. Pay attention to safety when fixing the lifting reel. Assign special personnel to command, ladder, scaffold, hand strap, etc., and check in advance to minimize the occurrence of accidents.

(3)卷簾門安裝好卷軸后，左右移動卷軸調整位置，用水平管和水平管檢查卷盤的高度。調整后，用帽螺釘調整光軸和卷軸。

(3) After the roller is installed on the roller shutter door, move the roller left and right to adjust the position, and check the height of the reel with a horizontal tube and a horizontal tube. After adjustment, use the cap screw to adjust the optical axis and reel.

安裝卷簾門的五大步驟到此就介紹完了，相信大家看完上述內容之后對防火門有了更深的認知，希望以上內容能對大家有所幫助，如對我們的產品感興趣，隨時歡迎大家前來參觀選購http://m.santoncc.cn。

This is the end of the five steps for installing the rolling shutter door. I believe you will have a deeper understanding of the fire door after reading the above contents. I hope the above contents can help you. If you are interested in our products, you are welcome to visit and purchase at any time http://m.santoncc.cn 。